The Voice of the Mountain Resort Industry  |  Est. 1962

Advertisement

Mountains Don’t Move Themselves

May 2010 Issue

Next-Gen Snowmaking

Automating your snowmaking saves time, money and labor.

Among resorts that make snow, snowmaking is the biggest line item in the energy budget. Typically, 67 percent of all energy consumed by resort operations is used in snowmaking. In many other departments, resorts have already acted to cut costs. Snowmaking now represents the last great frontier for cost-cutting and efficiency gains.

Two scenarios drive a strategic snowmaking plan: opening objectives, and resurfacing objectives. With both of these, it is important that all stakeholders agree on what trails are “priority one” and how fastest to meet the objectives of opening or resurfacing them. This strategic plan allows you to control expenses and maximize capital.

That might seem obvious, but logic doesn’t always apply when it comes to snowmaking. One area with several top-to-bottom, ultra-efficient automated trails always opened a manual trail first—even though that required 30 percent more hours to get open top to bottom. Why make this decision? “We just want to get that manual trail out of the way,” they said. Also, the manual trail went by the cat garage, so the cat crews voted for access on snow. A simple strategic change to an automated trail has allowed the resort to open top to bottom a week earlier than in the past (and a week earlier than its competitors) every year for the past three seasons.

MANAGING WITH DATA
Good data on snowmaking operations is essential. However, even though snowmaking is one of the biggest budget line items—and one of the greatest influencers of visits and guest satisfaction—many areas are managing blind. Even when the data is readily available, they don’t use or learn from it.

Here’s an example. For five years, Aspen had an automated trail that tracked all sorts of data, but no one analyzed it. When it was eventually explored, the data showed Spar Gulch had 5.1 million gallons on it, laid down at a balmy 25.8 degrees wet bulb. When the trail crew and patrolmen were asked if that production was enough, it turned out it was probably more than enough. So the next year’s production goal was reduced.

This past year—using existing data to manage snowmaking by volume, plus adding automation to 10 existing fan guns, and using a snow inducer—yielded impressive results. In a very thin early snow year, Ajax pumped only three percent more water than the previous season, but increased snow volume by 22 percent, as measured by an A/B volumetric test. Aspen used 16 percent less kWh and lowered labor costs by 14 percent. All snowmaking objectives were completed in the shortest snowmaking season ever, even though temperatures were three percent higher than the previous three-year average. Energy and labor costs dropped 23 percent, from $1,077 to $831 per acre foot.

AUTOMATION BEATS MANUAL
In another test, Aspen had two identical fan guns running several hundred feet apart. One was fully automatic, monitored from the control building out of sight and 1/2 mile away. The other was brand-new but had manual operation. At the end of one season of snowmaking, the automatic gun had flowed 30 percent more water. Other resorts that have monitored similar comparisons report even better results.

The lesson: automatic guns have a commanding performance advantage. For two reasons: they start automatically within minutes as temperatures drop through the 28 degree wet bulb barrier, and always go to the next bank and increase flow as temperatures continue to drop. In contrast, an eight-man crew tending perhaps 80 guns spread out over 900 acres will make those same adjustments “when they get there,” sometimes three hours behind the automated guns.

You can model the ROI all day long, taking into account the additional cost of automation vs. manual on that 30 percent gain, but that is only half the story. On the warming cycle of the curve, the auto gun is quickly turning off excess flow to keep snow quality constant. The unattended manual gun is flowing more, but making poor quality snow. At 28F wet bulb, the auto gun shuts off. The manual gun continues to pump out water—that doesn’t necessarily convert to snow—until manual crews shut it off.

In many cases, though, the crews decide to “run over the hump,” letting the gun run on minimum flow for hours, knowing that it will get cold again when the sun goes down. In a season-long test, we found that manual guns were run “over the hump,” above 26 wet bulb, 28 percent of the time. That is a lot of kWh conserved by automation when the computer determines it’s quitting time. See box below for an early-season analysis.

Here’s another case where automation helped. Wintergreen, Va., is 100 percent automated. In the first year the area doubled its seasonal pumping—not because they needed to, but because they could. Now, snowmaking manager Scott Gunnell uses the data from his snowmaking computer to build opening and recovery scenarios based on system data and the best weather forecasts he can get. He can track how many gallons are going to each gun on each trail. If he thinks the weather pattern is safe, he builds to the “no resistance” scenario, giving him maximum trail count in the shortest possible time and expense. If rain and thaws are coming, he builds to the “good resistance” level. He does this with three guys per shift, including him. As a result, Wintergreen makes only as much snow as it needs, and it makes that snow when the temperatures are favorable. You can see the differences in the chart on page 45.

LESS WATER & ENERGY, MORE SNOW
Lots of people have connected meters to snowguns to see how much water a gun is flowing. It’s also easy to figure out how much energy the gun is using, whether it is an a/w stick or fan.

But if that is all you test, you are not getting the full picture. How many gallons of throughput does a gun need to produce an acre-foot of snow? You need to measure the volume of snow in front of the gun to know whether you have a truly efficient gun. That’s done most commonly with a stake and grid test.

Holiday Valley, N.Y., has been doing these tests and found that today’s multiflow guns, with discrete, sophisticated nucleation systems, whether sticks or fans, are much better converters of water into real snow volume than the guns of 15 years ago.

We have found this to be true not just in cold temperatures, but in marginal temperatures as well. Using the same stake and grid test, Holiday’s crew found that it was using approximately 155,000 gallons of water to make an acre-foot of snow. That’s the best I’ve ever seen, and that number didn’t vary much whether the test temperature was zero or 22F wet bulb. Holiday’s test area included several different makes and models of multiflow, low energy a/w tower guns and use of a snow inducer additive. Deer Valley and Aspen have achieved similar results using late-model fan guns.

By comparison, 30 tests done with 15-year-old equipment resulted in an average of 300,000 gallons to make an acre foot of snow. The newer guns are better nucleators, so there is less evaporation. A lot less. Also, more droplets exit as frozen crystals, increasing volume. This means there is less water leaching through the pack or compromising quality.

In short: the efficiency of the newer equipment has created a staggering improvement that has perhaps gone unnoticed. There are still many poorly-converting snowguns in use out there, squandering water and energy.

Advertisement

Climb Zip Whip Leaderboard

BUILDING AN ROI MODEL
The ROI on technology is not simple to measure, but it can be done.

If you are replacing a resort full of first-generation a/w guns, or almost any technology more than 15 years old, with either auto fans or sticks, the ROI can be less than seven years on the energy and labor savings alone. If you can deliver increased market share, improved margin, and fill more beds in periods that can be influenced by trail count and snow surfaces, the return is faster. Wintergreen Resort is the best example of this (see “Put It on Autopilot,” SAM July 2007).

Many resort operators don’t like to consider the topline contribution of Blitzkrieg snowmaking in building an ROI. One western operator told me, “I don’t know what we make by having top-to-bottom skiing for Thanksgiving, but I can pretty much tell you what it will cost us if we don’t.”

If you are going to make the move to automation trail by trail, the return will come fastest from those “must have” priority-one trails, pipes and parks, where run hours are higher. Less temperature-efficient technology should be re-deployed on the priority-three trails, i.e., trails that can wait for sustained colder weather.

PIPES AND PARKS
Pipes and parks can be a brand builder, but they also use 25 percent to 35 percent of all snowmaking resources.
Here are some common-sense steps that will save energy, water, and time:

• Work with your builders before snowmaking starts. Exactly where do they want their 30 million gallons? Trail groomers and park builders have very different needs for snow placement.

• What water content do they want? For fixed tower guns to remain efficient, intermediate snow harvests will be required. Agree how often, and try to do it when temperatures are down for snowmaking.

• Pre-shaping features with dirt can save huge amounts of time and energy.

Snowmaking represents the biggest opportunity remaining in resort operations to dramatically reduce cost, open terrain faster and recover it quicker. It helps to build the pipes and parks that appeal to our core sliders faster, without compromise, and without breaking the bank. We need to embrace proven technology, gather all the data we can, and use it to manage snowmaking with a new level of professionalism.

Robin Smith, president of SnowConsult LLC, does snowmaking operational analysis and consulting for resorts. Contact him at (303) 842-2495, [email protected].

 

Sign in or enable JavaScript to keep reading.

Advertisement

Climb Zip Whip Leaderboard